home_icon
The World's Largest Online Bike Store
  • Lizard Skins Headset Cover
  • Lizard Skins Headset Cover
NOW$4.49
  • RRP$4.99
  • |
  • SAVE10%

Select  Colour
  • IN STOCK(5+)

  • right This item ships to United States of America
  • right Shipping amount : $9.99
  • right 365 DAYS to return or exchange
  • right Pay by Bank Transfer or PayPal or Card
A neoprene covering that wraps around your headset to keep out dust and water.
  • Colour: Black
 
Rated 4 out of 5 by 37 reviewers.
Rated 5 out of 5 by a bit of neoprene... lets be honest, its just a bit of neoprene, but its cheap and adds protection to your headset bearings. It wont set the world on fire, but its worth fitting! 21 September 2014
Rated 4 out of 5 by Good quality, good value for what it protects An essential bit of kit for winter riding, stops all the dirt and grit getting into your headset bearings. One tip I would recommend is if the paint quality isn't particularly good on your frame/forks, put a thin film of grease on them before installing this cover - I have found on my forks the paint has worn slightly underneath the velcro part of this after a couple of years riding due to the forks turning. Other than that it has kept my low quality OEM headset running smoothly for over two years of almost daily riding. A little tight at first but it loosens up with age. Might not fit 1.5" headtubes but fits 1⅛" no problems at all. 02 September 2014
Rated 4 out of 5 by Does the job Expensive for what it is (3" of neoprene and some velcro), but it keeps the the gunk out of your headset, so no complaints :) 28 August 2014
Rated 3 out of 5 by Sizing not adequate to cover 1.5" 44EEOS Nukeproof headset I bought a Nukeproof Warhead 44EEOS Headset combined with Nukeproof Turbine Spacer Pack 1.5" - used on Trutativ 1.5" stem. This headset cover barely was able to go round the circumference of the spacers ! ...and nor cover the height. So I ended up just protecting the spacers to prevent water from entering via the gaps during washing. Felt wasted that I cannot cover the bearings part. The width spec needs to specify. circumference. Think it will work well with normal 31.8" steerers though! 24 April 2014
Rated 5 out of 5 by Защищает и рулевую и раму Замечательная штука. Не знаю сколько прослужит, пользуюсь пока только 2 недели. Защищает не только рулевую но и раму от трущихся тросиков в рубашках и гидролиний тормозов. Закажу себе ещё парочку на 2 велосипед и про запас. 19 April 2014
Rated 5 out of 5 by Perfect for those wet n wild rides I've seen these over the years but never thought about buying until now, I ride mainly urban in all weathers all year round and found road grit can get into the bottom bearings on headsets during bad weather, only had this a couple of weeks but very surprised just how much road rubbish it keeps out. Highly recommended 31 October 2013
Rated 2 out of 5 Simple and would prob work, but doesn't fir 1.5" tubes. The idea seems good, but unfortunately it doesn't fit round a 1.5" part of the headset. 25 October 2013
Rated 5 out of 5 by Using it for more than a year, and can't ride without it. It keeps mine headset clean. Highly recommended. 03 January 2013
2 next>>

VIEWING