home_icon
The World's Largest Online Bike Store
  • Mobi Conversion Kit - 3 Metre
  • Mobi Conversion Kit - 3 Metre

Currently unavailable

We don't know when or if this item will be back in stock.

Mobi Pressure Washer Adaptor Kit

Genunine Mobi pressure washer parts. Ideal for universal connections.

Conversion Kit Features:

  • 100% Genunine Mobi Parts
  • V-15/V-17 Base Male Fitting
  • Buy Mobi Pressure Washer Accessories from Chain Reaction Cycles, the World’s Largest Online Bike Store.

     
    Rated 3 out of 5 by 1 reviewer.
    Rated 3 out of 5 by Washer Hose Converstion I purchased this kit to carry repair my Brand-X X-90 Pressure Washer. The original hose connections for the washer did not go the distance and I could no longer use my washer. So I purchased this kit and repaired my washer over the weekend. Here are a couple of tips. 1. at 3 meters the hose supplied in the kit is just too short. However, the connections are similar to those used on a garden hose, so I just cut the ends of the OEM hose that came with my washer and swapped the connections from the new hose. The outer diameter of the OEM hose is thicker than the kit hose, co be careful. 2. All threads are plastic and cannot take the same force as a brass or steel thread. Use PTFE tape or some other form of sealant and leave for a couple of hours before using. IT IS VERY EASY TO STRIP PLASTIC THREADS. 3. The replacement connection that screws into the pump unit is slightly bigger than then original. If you take your time it will screw into place though 4. If the plastic nut deforms any during installation of the new male connectors, trim them with a knife - any deformation may stop the female connection from closing properly. 5. I had to cut out a large hole around the outlet connector on my washer unit so that the hose could clip into place ok. It's a bit finicky, but with a bit of patience I got my washer up and running again. 16 September 2013
    1-1 of 1
    3 Questions : 4 Answers

    Product Q&A

    Ask your questions. Share your answers.

     
     
    « Back
     
     
    What are the differences between the Mobi Conversion Kit and the Mobi Hose Kit - 3 Metre

    I want to connect a mobi washer to accessories that attach to regular garden hose connectors eg other nozzles and car shampoo containers. I was looking to use the spare hose/connectors to construct an adapter.
    2 months, 2 weeks ago
    Customer avatar
    by
    Read all my Q&A
     
    Please wait while more information about hag6 is loaded.
    Additional information about hag6 could not be loaded.
    0points
    0out of 0found this question helpful.
    Was this helpful?helpful0unhelpful0

    Answers

    Answer: 
    These items will be compatible with a standard garden hose so you will therefore be able to attached other accessories.
    2 months, 1 week ago
    Customer avatar
    by
    Read all my Q&A
     
    Please wait while more information about crcsimon is loaded.
    Additional information about crcsimon could not be loaded.
    0points
    0out of 0found this answer helpful.
    Was this helpful?helpful0unhelpful0

    Answer: 
    It's hard to see any difference between those two kits.

    I'm not sure that you will be able to fit this to a regular garden hose, the conversion kit connectors are designed for a hose with a much smaller internal diameter than that of a garden hose.
    Age: 35 to 44
    Gender: Male
    Attitude: Just for Fun
    2 months, 1 week ago
    Customer avatar
    by
    Read all my Q&A
     
    Please wait while more information about MountainSnail is loaded.
    Additional information about MountainSnail could not be loaded.
    0points
    0out of 0found this answer helpful.
    Was this helpful?helpful0unhelpful0
    Does this simply connect to a Mobi washer where a hose would normally attach (i.e. nothing needs to be disassembled), or does it require removal of an existing connector to be replaced by the one in the picture?

    Your photo is not large enough to be able to tell. And I've had a look at my own washer, and the existing connectors do not appear to be removable!

    Thanks,

    Mark
    Age: 35 to 44
    Gender: Male
    Attitude: Just for Fun
    5 months, 4 weeks ago
    Customer avatar
    by
    Farnham,GB
    Read all my Q&A
     
    Please wait while more information about Lemming is loaded.
    Additional information about Lemming could not be loaded.
    0points
    0out of 0found this question helpful.
    Was this helpful?helpful0unhelpful0

    Answers

    Answer: 
    Hey Mark,

    This kit is primarily for V-15 and V-17 washers, but if your washer has the 'male fitting' shown in the centre of the image (left fitting, double click for larger image) which is threaded; it can easily be replaced and should work with your washer.
    5 months, 3 weeks ago
    Customer avatar
    by
    Read all my Q&A
     
    Please wait while more information about CRCAndyC is loaded.
    Additional information about CRCAndyC could not be loaded.
    0points
    0out of 0found this answer helpful.
    Was this helpful?helpful0unhelpful0
    the connector on my gun is a twist fit and would need to be replaced
    Age: 65 or over
    Gender: Male
    Attitude: Just for Fun
    5 months, 1 week ago
    Customer avatar
    by
    Mablethorpe,GB
    Read all my Q&A
     
    Please wait while more information about mobiman is loaded.
    Additional information about mobiman could not be loaded.
    0points
    0out of 0found this question helpful.
    Was this helpful?helpful0unhelpful0

    Answers

    Answer: 
    The 3m Hose will be supplied with Universal Click-On Base Male and Hose End Male Fitting Units shown below;
     
    Products related to my answer
     
    5 months ago
    Customer avatar
    by
    Read all my Q&A
     
    Please wait while more information about CRCLogie is loaded.
    Additional information about CRCLogie could not be loaded.
    0points
    0out of 0found this answer helpful.
    Was this helpful?helpful0unhelpful0
    1 of 1
    1 of 1

    VIEWING