Rated 4 out of 5 by Robye14 Very impressive motocross style rear mud guard.
Nice to see, very impressive. Easy to mount and well fixed in place, it doesn't swing while riding.
Unfortunately it's a bit short and doesn't catch all the mud. But it's good to keep saddle and adjustable seat tube clean.
16 April 2014
Rated 5 out of 5 by Mondraker The only item to buy
Great look like MX style,easy to install and does the job fantastic.So light and happy.
13 April 2014
Rated 3 out of 5 by Anonymous Больше нет, чем да
Крыло легкое с хорошей шириной и надежным креплением. Регулируется в широких пределах. Правда, длины немного все же не хватает: закидывает спину.
А самый большой минус в том, что гремит на неровностях дороги, даже на мелких кочках. Дико раздражает.
09 April 2013
Rated 1 out of 5 by Anonymous not great
Reviews and descriptions looked good, so I tried this to replace my SKS Crusher. It is rubbish in comparison. The wire loops are not long enough even for my Scott Scale seat post, let alone anything wide. Had to use zip ties and gaffa tape (which is what my old mud guards were latterly held on with when SKS packed in after 2 years). There is also a plastic screw tightener on each side of the guard (the white dot in pic). This cannot be tightened enough to stay in place over rough stuff and one has fallen out.... zip ties and gaffa tape again needed. The mud coverage is good, shame the fixings and screws are so rubbish. Get an SKS.
08 March 2012
Rated 1 out of 5 by Anonymous Poor
Wide but too short. Angle not adjustable to any degree. Awful scratchy metal fixing. Way too expensive. Cycraguard longer but not as wide at the tip (& have to dismantle clamp to adjust angle). Crud catcher I got recently has the lot.
THE Sportline front fender tho' is very good. Use that on the front with a Crud catcher on the back. If u don't want a big front mudguard, go with the frame mounted Crudcatcher (the Cycraguard one is smaller and flimsier).
16 December 2011
Rated 4 out of 5 by Anonymous good -just upgrade the bolts
These are good mudguards for MTBs, esp suspension ones. They do get in the way of seat-mounted lights, but you can put them underneath. They just get muddy.
You can change the angle; the only reasons to run high are your bike has so much travel that it would hit the rear wheel, or you have some rack-mounted tagalong that you need to clear (which my commuter does).
Main criticism: upgrade the low-cost plastic bolts on the side + top with stainless steel bolts. Not much money, but better
12 November 2011
Rated 5 out of 5 by Anonymous Brilliant product
its a reasonable price, and looks brilliant. Also came with a couple of stickers which was a bonus. My only worry was it was going to be huge on the back of my bike, but its just perfect. Very happy.
ps. those reviews saying its a little tricky to attach to you bike, WRONG! Took me a minute. It has 5 screws thats it, I recommend.
12 September 2011
Rated 5 out of 5 by Anonymous very nice fitting and looking item cheers
18 April 2010
Was this helpful?helpful0unhelpful0http://answers.chainreactioncycles.com/answers/5230-en_gb/product/prod10680/question/1214308/undohelpfulness.djs?format=embeddedhtml&sessionparams=__BVSESSIONPARAMS__&return=__RETURN__&innerreturn=http%3A%2F%2Fanswers.chainreactioncycles.com%2Fanswers%2F5230-en_gb%2Fproduct%2Fprod10680%2Fquestions.djs%3Fformat%3Dembeddedhtml%26scrolltotop%3Dtrue%26expandquestion%3D1214308&user=__USERID__&authsourcetype=__AUTHTYPE__&submissionparams=__BVSUBMISSIONPARAMETERS__&submissionurl=__BVSUBMISSIONURL__
Additional information about CRCBrendan could not be loaded.
0out of0found this answer helpful.
Was this helpful?helpful0unhelpful0http://answers.chainreactioncycles.com/answers/5230-en_gb/product/prod10680/answer/1189258/undohelpfulness.djs?format=embeddedhtml&sessionparams=__BVSESSIONPARAMS__&return=__RETURN__&innerreturn=http%3A%2F%2Fanswers.chainreactioncycles.com%2Fanswers%2F5230-en_gb%2Fproduct%2Fprod10680%2Fquestions.djs%3Fformat%3Dembeddedhtml%26scrolltotop%3Dtrue%26expandquestion%3D1214308%26expandanswer%3D1189258&user=__USERID__&authsourcetype=__AUTHTYPE__&submissionparams=__BVSUBMISSIONPARAMETERS__&submissionurl=__BVSUBMISSIONURL__